300-115 SWITCH Online Test-Implementing Cisco IP Switched Networks

At present, Our 300-115 SWITCH online test are the perfect way to brush up your skills, Take our 300-115 SWITCH online test for a run-through of commonly asked questions. You will get incredibly detailed scoring results at the end of your 300-115 SWITCH online test to help you identify your strenghts and weaknesses.

Our 300-115 SWITCH online test only offer 20 questions, it contains single choice and multiple choice,5 points for questions you get correct ,if you answer correctly part of multiple choice, you can get part of 5 points.

Begin to test now !

VTP is configured on switch R1. Which of the following features were added in VTP version 2 that were not previously supported in VTP version 1? (Select two)

 
 
 
 
 

The Company network administrator needs to enable VTP pruning within the Company network. What action should a network administrator take to enable VTP pruning on an entire management domain?

 
 
 
 
 

The Company switches have all been upgraded to use VTP version 2. What are two benefits provided in VTP Version 2 that are not available in VTP Version 1? (Select two)

 
 
 
 
 

You want to configure switch R1 to propagate VLAN information across the Company network using VTP. What must be configured on a Cisco switch in order to advertise VLAN information?

 
 
 
 
 
 

R1 and R2 are switches that communicate via VTP. What is the default VTP advertisement intervals in Catalyst switches that are in server or client mode?

 
 
 
 
 
 

You need to investigate a VTP problem between two Company switches. The lack of which two prevents VTP information from propagating between switches? (Select two)

 
 
 
 
 

Two Company switches are connected via a trunk using VTP. Which VTP information does a Catalyst switch advertise on its trunk ports when using VTP? (Select two)

 
 
 
 
 

What is a characteristic of assigning a static VLAN membership?

 
 
 
 

The VLANs in switch R1 are being modified. Which of the following are updated in R1 every time a VLAN is modified? (Select all that apply)

 
 
 
 
 

You are assigning VLANs to the ports of switch R1. What VLAN number value is an assigned to the default VLAN?

 
 
 
 
 

In the three-layer hierarchical network design model; what’s associated with the access layer? (Select two)

 
 
 
 
 
 

The Company LAN switches are being configured to support the use of Dynamic VLANs. What should be considered when implementing a dynamic VLAN solution? (Select two)

 
 
 
 

The Company LAN switches are being configured to support the use of Dynamic VLANs. Which of the following are true of dynamic VLAN membership? (Select all that apply)

 
 
 
 
 

The Company LAN is becoming saturated with broadcasts and multicast traffic. What could you do to help a network with many multicasts and broadcasts?

 
 
 
 
 

Which of the following statements is true about the 80/20 rule (Select all that apply)?

 
 
 
 

What are some virtues of implementing end-to-end VLANs? (Choose two)

 
 
 
 

If you needed to transport traffic coming from multiple VLANs (connected between switches), and your CTO was insistent on using an open standard, which protocol would you use?

 
 
 
 
 
 

Which two statements are true about best practices in VLAN design? (Choose two.)

 
 
 
 
 

Which method of Layer 3 switching uses a forwarding information base (FIB)?

 
 
 
 
 

What is needed to verify that a newly implemented security solution is performing as expected?

 
 
 
 

Question 1 of 20

 

buy

Leave a Reply

Your email address will not be published. Required fields are marked *