500-005 TX9KMAN Online Test-Installing Cisco TelePresence Video Immersive Systems

At present, Our 500-005 TX9KMAN online test are the perfect way to brush up your skills, Take our 500-005 TX9KMAN online test for a run-through of commonly asked questions. You will get incredibly detailed scoring results at the end of your 500-005 TX9KMAN online test to help you identify your strenghts and weaknesses.

Our 500-005 TX9KMAN online test only offer 20 questions, it contains single choice and multiple choice,5 points for questions you get correct ,if you answer correctly part of multiple choice, you can get part of 5 points.

Begin to test now !

An end user has reported that the TX9000 TelePresence Touch 12 screen does not power down. Which option is the correct response?

 
 
 
 

The TX9000 fails to boot completely and is stuck on Step 5 of seven steps as displayed on the Cisco TelePresence Touch 12.
Which step should be implemented to correct the problem?

 
 
 
 

If the TX9000 system is experiencing “phantom switching,” what should be done to troubleshoot the problem?

 
 
 
 

The TX9000 center speaker connects to which component?

 
 
 
 

The TX9000 left and right speakers connect to which component?

 
 
 
 

What is causing the Cisco TelePresence Touch 12 to show Project/LCD in error?

 
 
 
 

Which two options cause the presentation to not show on the Active Collaboration data display and show only in PiP on the TX9000 plasma screen? (Choose two.)

 
 
 
 
 

What is the function of the Presentation Devices test from the Cisco TelePresence Administration GUI?

 
 
 
 

When a laptop was connected to the TX9000 presentation codec and the Presentation icon was tapped on the Cisco TelePresence Touch 12, the presentation sharing failed. Which option corrects this issue?

 
 
 
 

When the TX9000 boots up, green progress check marks are displayed on the screen.After successful bootup, six check marks are displayed. Which of these can cause the fourth check mark to fail?

 
 
 
 
 

When the TX9000 boots up, green progress check marks are displayed on the screen.After successful bootup, six check marks are displayed. Which of these can cause the last check mark to fail?

 
 
 
 
 

In order to place a call to 5001 using the CLI, which command is correct?

 
 
 
 
 

After DHCP is enabled and a new TX9000 system is configured in Cisco Unified Communications Manager, the TX9000 displays an IP address of 192.168.100.2, which is not what was expected. Which of these should be verified in your troubleshooting of the issue?

 
 
 
 
 
 

After the initial bootup of a TX9000 system, you notice that the software version on the codec is not what was expected.Which location should be searched to ensure that the desired software is available on the TFTP server for the codec to download?

 
 
 
 
 
 

In which situation would a new TX9000 system boot up as a Cisco TelePresence System 500-32 device?

 
 
 
 

What is the build number for the following Cisco TelePresence System image?
cmterm-CTS.1-9-1-68R-K9.P2.cop.sgn

 
 
 
 
 
 

Which Cisco Unified Communications Manager GUI is used to upload a new Cisco Option Package file before the TX9000 can be upgraded?

 
 
 
 
 

When fine-tuning the TX9000 displays for optimal performance, what is the primary factor in getting the optimal color temperature for the displays?

 
 
 
 
 

Which component is used to calibrate the TX9000 system microphones?

 
 
 
 

Which adjustment screw is used on the cameras of a TX9000 to fine-tune the yaw?

 
 
 
 
 
 

Question 1 of 20

 

buy

Leave a Reply

Your email address will not be published. Required fields are marked *